circuit

I made a circuit to demonstrate the work of a 555 and a constant current regulator and wanted to add triangle wave input. I've done that by integrating the output of a 555 timer, and at the node 'tri' I do get the desired triangle wave of ~ +-8V. Since I want the the voltage positive at all...

Hello, I am not too strong with building electrical circuits so I am just wondering if I could get some feedback on the circuit I built. I am trying to connect a 12V inductive sensor to a Raspberry Pi 3B+ 3.3V port. The inductive sensor is being used to detect a metal sleeve inside of a valve...

Hello, I have built this motor circuit for my Arduino and when running it only gets less 1v and the motor spins very slowly and my bigger motor doesn't spin at all. I have attached the diagram that I followed below. The Motor should be getting 5v from the Arduino although something seems to be...

Hi Everyone, my DT project includes an inductive charger. I would like to build a circuit that when a voltage is received from the inductive charger (9Vdc in ~5Vdc out) one LED blinks then after 10s it remains constant. Then turns off when voltage is stopped. I’m not entirely sure how to go...

Hello guys, how are you all doing? During the past few months I've been going through the Textbooks AAC has published, experimenting with some minor circuits and even PIC microcontrollers. I've learned a lot during the process and decided to do something a bit more challenging - make a basic...

Hi all, Newbie to both this forum and electronics! I have a somewhat old Casio CDP-100 with 8 keys that went dead recently. All other keys are fine and speakers/power are working perfectly. Schematics here: http://www.warningwillrobinson.com.au/manuals/Casio%20CDP100%20service%20manual.pdf...

Hi, I'm new in the forum and I don't know much about circuit but I have a problem and would like your insights! I have this toy called B Symphony. Is a great music toy, you can google it and take a look. The point is it got wet and the main circuit suffered some damage. I cleaned it but know I'm...

Circuit problem: I have the answers to it, but I need to know the process of how to get there.

Hi everybody! Hope you're good! :) I'm strugglin since some days on that nice muscial tool. I've replaced some faulty switches. Replaced them with new one from Mouser. Sadly I've managed to hurt some VIAS connecting both side of the board. Luckilly enough this is just 2 layer board (top/bottom)...

Hi, all. I have downloaded an L293N motor driver for my Proteus 8 Professional from the following website. https://www.theengineeringprojects.com/2017/09/l298-motor-driver-library-proteus.html Based on the video link in the website (or you can click here: ), it says that the 2 pins (unknown to...

Hi all, I am currently working on this robot with the guidance of the following website "https://circuitdigest.com/microcontroller-projects/obstacle-avoiding-robot-using-pic16f877a" The circuit diagram is as shown below The L293D motor driver module he used looks something like this while...

I have a vixen DD-2 telescope controller, which is not working. In my cases the LED on the controller doesn't lighting up. The controller remote is rated 12V/ 0.96A. I have confirmed the capacities of all the capacitors and the voltage at points A to E: A : 12.1V B : 12.1V C : 0.5V D: 0.9V...

I need to design a circuit to calculate the product of two 4-bit binary numbers, and then display the decimal result in three HEX displays.I already have the multiplication part, but the hex baffles me since : 1-The inputs are two 4-bit binary numbers. 2-The system can display each input...

Hello, I've been having difficulty dealting with circuit analysis. Here, for example, I'm given the task to find the voltage on Vs. But I fail short half-way through. Also, I don't understand how to deal with negative voltages and/or currents, and would appreciate help! My attempt at solving...