circuit design

Hi, in IEEE 3 bus, why are circuit breakers connected at the 'load' rather than connected at the 'generator and load'?

I have always used Eagle for my designs because it is free, well supported and nice UI. Recently I received a design in Kidcad which I tried to export to Eagle but I was unable to do so. Then I thought, hey! why not using Altium, because I see that most of the job offers for Hardware design as...

I made a circuit to demonstrate the work of a 555 and a constant current regulator and wanted to add triangle wave input. I've done that by integrating the output of a 555 timer, and at the node 'tri' I do get the desired triangle wave of ~ +-8V. Since I want the the voltage positive at all...

Hi! I'm a student of Electric Engineering and I got a problem on a Electronic project. I have to make an 8-bit shift register with serial input and serial output. The basics of the project is that it has to have two push buttons: one will be a logic 1 and the other a logic 0. The shift register...

Hi. I am trying to build a power supply which output is 2000VDC and 20mA (40W) input is 220V ac (european input). I thought I can use flyback transformer. And I started to design. I selected duty cycle as %50 and frequency as 50kHz (actually I don't know how to select frequency and duty cycle...

What does pull up mean? In circuit examples, for example for a ESP8266 chip, pull up is connecting to Vcc through a 10kΩ resistor. Why 10k? How is this value derived? I have seen two separate cases of pull down. One connects to a 10kΩ to ground while another connects directly to ground. Hope...

Hi, I need to connect 5 wire from pcb to outer terminal, whether soldering the wire is a better method, or is there any other method for connecting the wire with pcb. it should withstand even in hard environmental conditions. Thanks, D

Hi guys, this is my first post here. I hope I'm in the right section. I've made a slayer exciter with a 22kohm resistor, a 2n2222 transistor, using a 9v battery. My secondary is 0.25 mm and 10 cm in lenght. My primary is 4 turns. I wanted to obtain some sparks, and I added a 47k instead of 22k...

as I want to calculate the transfer function of circuit that is meant to generate source current using an Op amp as control loop, I need the gm and r0 of the mosfet(to determine the transfer function of the Op amp current source with nMOSFET) here is the picture of MOSFET with showed parameters...

Hi Everyone, my DT project includes an inductive charger. I would like to build a circuit that when a voltage is received from the inductive charger (9Vdc in ~5Vdc out) one LED blinks then after 10s it remains constant. Then turns off when voltage is stopped. I’m not entirely sure how to go...

Hello! If you need a PCB designer to help you with one of your projects, then I may be able to help! I'm offering my services at a low cost at the moment, so hopefully this proposition is interesting! I've been in the electronics industry for approximately 3-years at this point and over that...

<picture 1> Hello I'm from South Korea. I need help about this circuit. Picture 1 is typical connection about IR2101 this is my circuit that i designed. I want to know how it works. I want to know about working principle. 1. HIN = High, LIN = High -> Output "U" = ? 1. HIN = High, LIN =...

Dear Friends, I am working in an Electronics Manufacturer service (EMS) and we do PCB assemblies for Automotive products (ABS). We are getting many field failures due to components burnt issue. Mostly like diodes, ASIC, MCU and FET components are getting damaged/burning in the field. Whenever...

Howdy, so I am currently working on a small project to build a binary clock style watch. I am pretty new to circuitry and building small circuits. I do know some python and have been toying around with my raspberry pi 3B+. Here is the link to the project I plan to replicate and modify for my...

Hello all! For the last project for my application of ICs class, we have been tasked with updating Northrop and Nilakhe's No-Touch Ocular Pulse Measurement System. I attached the assignment specifications that I was given as well as the article itself that is mentioned. I've read a lot of...

Hi, all. I have downloaded an L293N motor driver for my Proteus 8 Professional from the following website. https://www.theengineeringprojects.com/2017/09/l298-motor-driver-library-proteus.html Based on the video link in the website (or you can click here: ), it says that the 2 pins (unknown to...

Hello iam trying to connect 2 MSP432E mcu's to one ethernet port, iam thinking a 3 port ethernet switch would work or a optical isolator would work.I was curious if other ways exists such as just being able to connect both Mcu's ethernet traces to each other.any iput is appreciated thanks