signal

Hi All, I've attached a PCB layout I'm working on (minus the board itself). I set it up a funtional(?) version on a solderless breadboard first, BUT it doesn't work. I've been studing 555/4017 diagrams till I'm crosseyed and I can't figure out why... :confused: Thx, Joel

i sincerely greet the entire community i have difficulty understanding the output of this system, i.e. y(t), I have difficulty understanding y(t) = v(t) − h(t)*y(t) I know this is the right output. but I need to understand the logic of how this happened. actually, what I see is this: y(t) =...

i salute the whole community i'm working on convolution, but there's a point I don't understand I use the general formula of the convolution as follows : and I draw the graphs accordingly, and after I draw, we need to Decouple them, find the space in between, and find the convolution...

I have 03 different pairs of shielding twisted cable (STP) all going side by side and are connected to an LRU. 02 pairs are of input while one pair is of output from LRU. Pair 1 has power supply of 5v and ground. Pair 2 has voltage input in mv with ground. Pair 3 which is the output pair has 03...

I am working on implementing the attached paper in MATLAB. I have successfully implemented the transmitter, but I am facing challenges with the receiver. The main issue is that the Zero-Forcing (ZF) equalizer (i.e., the inverse of the HH matrix) does not provide an acceptable BER when τ<1...

Here’s the information I know now: The comparator I’m going to use is MAX40025. The output impedance of the common base amplifier is 300ohm(Rc), the input capacitance of the chip is 2pF. I would like to transfer a fast signal to the comparator(over 45MHz). What should I consider when connect...

I have a steel container utilized for beer fermentation, housing an iSpindel hydrometer sensor immersed in the liquid. This sensor transmits data through 2.4GHz WiFi. To enhance signal strength outside the vessel, would it be beneficial to affix two passive omni 2.4GHz antennas to the lid...

I have the LTC2668 on my board, I am doing signal verification on it. https://www.analog.com/en/products/ltc2668.html#product-overview I found that all SEL1~8 outputs have weird drop of voltage before the main pulse as shown in the waveform below (this sudden voltage drops always happens at a...

As the title says I want to buy this Wifi Signal Repeater Router Range Extender and price seems good but I worry about quality. Its about this one - https://aliexpress.com/e/_DBrAU1x Any help is wellcome, Thanks!

Hello. I am new to electronics and I am trying to complete an LM386 audio amplifier that includes a bandpass filter between 5 and 33 Hz. I know some of the frequencies are outside the frequency range humans can hear. I am testing using a function generator on NI Multisim to get around this. My...

How do we get td1 - td2 = 2ns? I have no IDEA about how to adjust delay cell ,Thanks solving my problem , Thanks a lots

I want to know 10 bit SAR ADC , supply voltage 0.5V , Vcm based , after DAC switch 9 times , how to measure DAC input Dynamic range ? I need to know voltage range that I can use Voltage to time Converter transfer the voltage to times Thanks everyone reading Sample_N = DAC's N node...

Hello, first of all, I'm sorry if this is not the place for this thread. I want to ask, whether is my understanding about sine and cosine in real life is correct or not. I came across this a question(about conventional DSB AM to be specified), where we have two signals m(t) = 2sin(2000*pi*t)...

hi to all i have a question about the AM signal power in am modulation in attach file i have derive the power of am signal but ther a term <m(t)> is the mean value of message i can ignore this term generally or in the case where the m(t) have zero offset? thank you George

Greetings, I'm new to electronics and am interested in the field just as a hobbyist. I've read the Complete electronics self teaching guide by Boysen and Kybett and am now moving to Basic Antennas ARRL and Building your own transistor radios by R. Quan. To be honest im attracted to RF...

Hello, I designed attached circuit to drive H Bridge. My generated input signals are in attached picture, duty cyce that I am using is 40% for each signal, 99 kHz frequency. As result I am getting really bad shape of signal on R9 resistor. I am no getting steep signal when I turning H bridge...

Hi, can anyone help me with ideas on building devices that produce an audible signal when come close to each other, say 2 meters or less. Both devices continue signalling until they are two or more meters apart. Think about a microphone moved close to a speaker - you hear an unpleasant...