motor

Hi all, I got a Delta 50-761 dust collector second hand and it has been giving me trouble. It turns on, fan runs, but it blows the start capacitor within seconds. I replaced the capacitor and it did it again. I looked at the centrifugal switch, thinking it might not be functioning and causing...

wlpThis circuit is a low side current measurement of a motor using a shunt resistor and adc of a mcu. However, I do not understand the reason or use for the 100k internal pull down resistor, 10k external serial resistor and the capacitor. Anyone can help?

Hi, I have an electric hoist trupper brand, this comes with a control and a switch that disables the ascent after a certain point, I want to add another to disable the descent. I tried putting the switch between B and 10 but it disabled the up and made it go down if I pressed up or down. I...

I am using one machine (which has a small motor) which has battery of 1.2v which got dead and i want to change the power source to USB. The battery is of 1.2V and 400mAh. Motor connected to works perfectly fine if provide the 1.2V from bench power supply. I want to use USB power supply instead.

Hello Guys, I m searching for a Cheap Motor for an E Scooter project. I find this one...

I have to use a 94V battery to power a 24V DC motor and looking for suggestions on a motor controller that will help with the buck converter aspect and in rush current of the motor? Im a student so still trying to learn the best way to do this and was told this may be the best approach? The...

Hello, I have an arduino Uno that I am trying to use to control a 12v motor. I need to control this motor. I have tried using the analogWrite(); method, and also changed the frequency but still could not get my valve to move. This valve can be controlled via linbus or pwm according to the...

Just found this on ali they said its wholesale action and they are in hurry to sell them all. Its that normal price or its really cheap? Please check - https://.aliexpress.com/e/_DBQRbZt I need around 100pcs. Any suggestions is welcome. Thanks!

Hi, To give you some background I am currently working on an Automated machine for Manufacturing that involves two air-blowers that are powered by 3-phase 208V power. The blowers are set-up in independent circuits with a Schneider 3DM2-WRDBWZ EOCR and 10A/20A MCB after the EOCR. One of the...

I have been working on an Electro-Arc tap burner in the machine shop. The power feed mechanism only works partially, as the feed-rate potentiometer seems to have no effect on the actual speed of the motor. We confirmed the potentiometer to be in working order so I believe there is a fault...

Hello! Im an indoor electrican apprenticeship student and I need help with solving a task we we're given, since I can't seem to figure it out. A little context too: on the photo you can see a motor diagram, the thing is, when u press both the start buttons and all the contactors go down, you...

First the picture, because a picture is worth a thousand words. Is this possible? If the light is OFF, then the motor stops. Low light brigthness = low motor speed. High light brigthness = high motor speed. Thanks.

I am following this connection to get a driver to an Arduino and a step motor. The original connection is this: Green wire --> Step Blue wire --> DIR Red wire --> +5V My driver, However, has different pins. How can I connect to my driver? My driver:

I have a power supply that automatically shuts off when an over voltage condition occurs. In my case, my load is a DC Brushless 3 phase motor (draws about 600 W) and it's triggering an over voltage condition for the power supply whenever I slow it down. If I don't care about efficiency and I'm...

I need to build the motorized pinwheel project in proteus. Arduino 328 should be used as seen in the 2nd photo. I will be grateful if you could help me.

I have searched all over and have not found an answer. I am a newbie, please bear with me, I'll try to explain as best as I can. I have an alternator which I assume has a 3 phase wye configuration. I am planning on removing the rectifier. I would like the alternator to supply power when it is...

Hello, I'm trying to redesign the electronics for a camera's stepper motor controlled pan/tilt/zoom/focus features. The product is from China and there is no documentation available. I've managed to determine what parts were originally used to control the motors but there are no datasheets...

Hello dear Forum, I am new here. I don't have much knowledge of solar panels or motors... I was wondering how it would be possible to connect a small/medium solar panel (not too expensive) to a mirror ball motor (for a 50cm diameter disco ball). I don't have any of the materials yet, that's why...

There is a peculiar issue noticed, I need help understanding the reason and may be troubleshooting. There is a microcontroller(87S52) based board with ADC and IO lines. The unit is programmed to operate for a time lets say T secs. When the board is used in the system in stand alone mode, I tend...

I'm working on a 3 phase 20HP motor which its wiring does not match the the name plate. It does not have the traditional 9 or 12 wires sticking out the side which can be reconfigured for 230v/460v. Splitting it apart reveals a total of 24 wires, 9 pairs, 1 triple, and L1,L2,L3. Analyzing the...