help

I have bought this Delay Relay module off of amazon. I am using it to make a circuit that will act as a latching relay with a delay for a 12V power source. The circuit should work as follows: There is a switch to activate the relay. When activated, the relay will remain on until the 12V power...

Hello, fairly new to all this but done my best to get to this stage! Im repairing a pottery wheel and am looking for a modern replacement for a STOPCIRCUIT GDU-2U-73-P1. As i understand this is a panel mount 2a, trip curve c, circuit breaker with an auxiliary contact. Looking through spec...

So hello:3 I have already tried many things, and looked at many things, but I can't implement any way to read a value from my data table character by character here code: Morse: mov DPTR, #Text ; Point to the beginning of the text mov...

Hi all, I'm looking for some help with a light switch from the rear interior lights of a Vauxhall Insignia. I've scoured the internet with the parts numbers and manufacturer assembly numbers etc and came back with no results. All I know is that this is an on/off push button switch made by...

Hi all, First, for you ADHD go-gettum problem solvers who like staring at funny graphs that aren't doing what they should be doing, the TL;DR: There's a funny electronic buzzing sound in all of my sensitive/expensive electronics and it's even gotten louder; please help me understand this...

Hey guys, I am trying to diagnose what the issue is with my Kurzweil CUP2 digital Piano The piano displays no sign of life besides a red on led. LCD screen does not display anything Buttons do not seem to do anything(there is a little red light above each button that indicates the "mode" it is...

Hey guys, I am relatively new to micro electronics, and am in desperate need of help! I want to bypass the muting circuit in a electronic piano. This involves either activating the relay, or pulling it to ground (BA3-5 Relay, and the highlighted LS1 in the picture below). Please could someone...

Hi. A friend gave me a JTS JS-1E large diaphragm condenser mic that has been partly disassembled and needs some soldering. Seems to be quite simple but Im not sure how it should be wired. As shown in the photos there is an M- and M+ that I think need to go to the diaphragm but I don’t know where...

I designed a circuit to process input from a sensor with a range of -300 mV to 300 mV. The desired output of the circuit is 0 V to 600 mV. To achieve this, I used the op-amp equation Vout = Vin + 0.3 as a basis for my design. However, when I simulated the circuit, the output was only around 900...

Hi all, Question for any of you who may know: How does mobile robot charging work safely? I notice a lot of delivery robots are designed with these large contacts (boxed in red below), but how are these designed to prevent them from being live contacts in case of customers accidentally...

Hi everyone I need to make a circuit with the following elements: The output will be a siren connected to a 230 V and 50 Hz network. The control circuit will use a 9 V battery as power supply and an operational amplifier must be used, the siren will be activated with a relay. The alarm will...

As the title states this is my first PCB I have designed purely through documentation, I have this designed through breadboards and breakouts but am attempting to put it all onto a single board so I can scale it down after I know it all works. Are there any people I can talk to to fix design...

I have a little experience with wiring after having to hot-wire my aftermarket radio in my car when changing it out, however I do not know how to fix this issue. The wires in the plug were loose and the lights were not turning on because of this, so i cut it off and figured it'd be as simple as...

Hi, I bought a claw machine and there seems to be a problem with the motor control of the claw going up. when the claw is going up it will go for a brief period and then stop, the motor will stall and it throws an error (claw not going up) . Motor seems fine 28v 0.48a when powered with bench...

I have an RF Explorer to use to scan what RF's are around me. I am curious as I'm am just getting in learning about wireless transmission and propagation. However I can't explain these power levels of -10 dbm all the way to -0. The RF Explorer does seem to be working correctly just based off of...

I'm pretty newbie. i designed a boost converter as hobby and need some help about that. not sure if it will work. how can i fix or improve the circuit. i aimed 5 Vin and 15V 10A max out and use 555 for generate pwm signal for mosfets. But i know 555 can generate max %50 duty cycle and it means i...

I found a blog that shows how to build a digital clock using ICs cd4060 and cd4026. https://danyk.cz/hodiny_en.html This is the site. I have checked if my ICs are working and they are. The only output I'm getting is the every 7 segment display shows 0 and the the two decimal points blink every...

I have watched recently this video: At the end of it he describe a way to make edge detector by using capacitor and resistor. The thing is i don't see it being discharged in any way. Would't it make it impossible to charge again and in consequence make current flow through the resistor and make...

Im trying to put a bcd input into a 7 segement display, but as it only shows the numbers 4 to 8 correctly, in all other numbers all of the segments are on, does anyone knows why? you can see the binary input on the right video...