Facebook
Google
GitHub
LinkedinBlogs
Hi everyone I have a problem with overheating resistors.
So basically it's a 24volt vehicle that had normal globes as rear lights I have replaced them with led lights the reason I put resisters is because the light module is picking up that there is no globes present and shows faults. The value...
I decided to make luxmeter, which has basic functions:
1. measure lux from 0 to 188000 lux
2. calculate watts/m2
3. charging using USB cabel via TP4056 board
Basic sensor is MAX44009, which measure lux. I use Arduino Pro Mini as microcontroller.
Totally it cost cca 13 $. Case is homemade...
I made a transformarless power supply 12v. But when i run it, it light my leds but the 5w resistor and 470uf capacitor getting too hot. I can't touch for minitues after i run it for less than 1 minitue it because of hot.
Iam planning to build a rich bass speaker, but really want to know I'd my component marched to each other to give out a sound powerful delivery.
1. 50w × 2 dual channel amplifier( 12v)
2. 50w x 2 full range 4" bass speaker.
Then the challange I am having how is the find out how many lithium...
The symbols of Logic gates, OR, NOR, XOR, AND, NAND, Buffer, Inverter, Schmitt Trigger.
The symbols of L, C, R, Pot, Diode, Zener, Bjt, LED, Xtal, SCR, N, P MOSFET.
Pls my bluetooth speaker fell off my and hit the floor, since then the speakers( drivers ) changed. Anytime you played it it will be sounding like the speaker burst; "Po po po" pls what may be to cause and how can I fix it?
Hello, I post this on this forum, because I have a request that’s I don’t find the answer on internet.
I want to make a stroboscopic lamp for my airsoft gun.
My electronics skills are a bit higher than basics.
I watched a lot of YouTube videos, but none was comporting a 3 led working under 5 V...
Pls can anyone help me to figure our where to connect Bluetooth module to this amplifier. Am just new on the DIY Bluetooth speaker project.
I will appreciate your kindly direction and expert advice.
Hi, all...
New here.
Fired up a recent circuit having S8050, NPN transistors. (BJT)
I could see it was conducting from Collector to Emitter.
Thought I did something wrong, so I flipped it around.
It still conducted. *&^%$#@! argh.
I can't have the circuit conducting BOTH ways.... and I don't...
Has anyone made a lamp with a working meter in series?? Was wonder if any one had a diagram or could help me with wiring it up. Thank you.
[1]: Motivation
AC loads are everywhere around us because at least home appliances are supplied with the mains power. Therefore, we always face the situations that we want to have full control (dimming) over an AC load such as a lamp, a motor, vacuum cleaner … etc.
We should know that...
An FM transmitter is one of the most popular devices between electronic hobbyist, professionals and even non-technical people. In this article, we gonna learn to how to build an easy, stable and digitally controllable FM transmitter.
For this design, I have selected the VMR6512 module which...
Embarrassingly, it seems 'off-line life' has -once again- made 'liars' of us:rolleyes: -- That said, I can imagine no scenario preventing either of us returning to regular participation next week (i.e. that of Mon May 13, 2019).
In the meantime I'm pleased to have found made time for the...
An obstacle detection unit is an essential part of a variety of projects, such as robotics and security applications. The infrared sensors are widely used for these types of applications. The main drawback of some circuit designs is that the detection units are sensitive to the outside lights...
Almost in any circuit design, building at least one regulation stage is necessary. Two power supply design options are available, which are linear and switching. The linear regulators are easy to build but inefficient, especially when there is a high difference between the input voltage and the...
FM transmitters/receivers are one of the top favorite circuits of every electronic designer. An FM transmitter is one of the first circuits that an electronic enthusiast decides to build.
For this purpose, instead of using discrete components and building one of the traditional transmitter...
Reality = sum I=1 to infinity
Of perceived_reality sub I
+ Actual_Reality
{
{\mathrm{P}(reality) =}\\
{\sum\limits_{i=1}^{\infty}\mathrm{P}(perception_i) +}\\
{\mathrm{P}(reality)}\\
}
