pwm

Hi all, I am trying to build some underwater lights for my boat. I am using 10 pcs of 3W RGB 6 pin leds in series and i have tested the output. I am currently using a constant current constant voltage driver. I would like to make a pcb capeable of driving the 10 leds and controling them with...

Hi, I have returned to an old issue I am struggling with – my door lock solenoid project again. I have created a really simple LTSpice circuit driving my solenoid at 1Khz, 50% duty. The solenoid I measured with an inductance meter, 35mH and 25R series resistance, this has been entered into the...

Hello all, I have encountered an AHC244 chip used to drive LEDs (Something like in the attached image) so I wondered why not just drive the LEDs with the uC pins? And also I have seen this IC used with some PWM signals as inputs to it! in this case, I am guessing the output would be the same...

Please help me to understand this circuit about analysis voltage each point and how to calculate time charge and discharge time on triangle signal. If use Op-Amp NJM2904C Thank you.

Hello, I have an arduino Uno that I am trying to use to control a 12v motor. I need to control this motor. I have tried using the analogWrite(); method, and also changed the frequency but still could not get my valve to move. This valve can be controlled via linbus or pwm according to the...

Not usually one for asking questions in forums, as I'm usually able to find solutions with my own research, however, I've been looking at this over a period of days now, and the deeper I dig, the more confused I'm getting.. I'm a Computer Science student, not electronics, so please go easy on me...

hello I have a practical task to make a simple LED lamp. I was using LDD-1000 for that purpose. But it does have minimal duty cycle of 20% (output is filtered so it's 20% of max. current) . Was looking for an alternative that could provide smooth control of current from 0A to 1A. Kinda lost in...

I am attempting to use a thermistor to control the PWM of a 555 output. Ideally, I want the duty cycle to be 100% when hot (~90°C) and 0% when not hot (~25°C). I am doing so by placing the thermistor as R2 (RB) in astable mode with a forward biased diode in parallel to R2 (allowing a duty cycle...

Hi, This probably isn't super complicated but I have to control 3 stepper motors simultaneously with an esp32 for part of a robotic arm. These are the nema 23 stepper motors I am using, they are normal open loop 4 wire stepper motors. These are the motor drivers I am using. One pin tells...

I want to make a circuit that will convert a PWM signal to an analog signal. I want the circuit to be able to work on higher frequencies as well though (up to 15 kHz). Would an RC filter be the best method? Any reference design examples for this?

I'm trying to determine a standard PWM frequency output for RGBW controllers. I see a lot of constant current LED chips call out a maximum PWM frequency input between 300 and 500 Hz. 1. I assume this indicates that 300 to 500 Hz is standard? I've seen a 12 Vdc 385 Hz RGBW controller pass FCC...

Questions: 1. Why do switching regulator ICs have dedicated PWM inputs pins? 2. Can you use PWM on a low side switch at the output of a constant voltage buck regulator module? For instance Remcom Power's R-78E5.0-1.0. My concern is that dedicated PWM inputs operate differently than using an...

Detailed description and website link are below. Parameter: 1>.Product Name: pWM 4-Wire Fan Temperature Controller 2>.Work Voltage: DC 11V~55V 3>.Work Current: 0.1A(MAX) 4>.Fan Current: 5A(MAX) 5>.PWM Range: 5%~100% or 0% 6>.PWM Frequency: 20KHz/2.5KHz 7>.PWM Signal Amplitude...

Hello, I have to design a single op amp circuit that has only +15v, -15v and GND as input and outputs a symmetrical PWM signal (+V and -V) with adjustable frequency and duty cycle. I have something that works partly but not completely, I can adjust the duty cycle from ±60% to ±100% but af that...

Hi, I come from the background of microcontroller design. I am learning fpga design. Usually in the ucontrollers the total number of pwm is limited as per the vendors. In FPGA how can i determine the maximum number of pwm I can drive from a fpga. For example, currently i am working with...

Hi, My project diagram is similar to this idea, Lets say input is 3p 380VAC, 60Hz, Main Transformer MTR runs at 20kHz, DC output should be 50-147 v, charging current 100A. Should have CC and CV mode of operation. I need to implement FW with following facilities, 1. Shunt/ Temperature...

I am making a boost converter following this Tutorial but I don't have the exact MOSFET. I have 2 motherboards laying around and they have some MOSFETs on them some of the names are: P3055, K3918,6670AL(datasheet inserted). There are high switching speeds but the datasheets don't have the max...

I have given the following C-Code to test a 60V DC motor with [gear box ratio 16:1 and incremental encoder to see if the code calculates the speed by reading the Pulse signal as feedback for µcontroller from encoder. The µcontroller is ATmega88A-UA. The encoder RE56-3-1000-TI signals 1000 ppr...

Greetings, I am new to this esteemed forum and require some assistance and advice. I am trying to locate the related V+ and V- on my treadmill board (B102S S07 Shanghai Elect) to hook up on a Signal Freq Gen (XY-KPWM) to run my DC motor. Background: My treadmill console acts faulty...

Hello, I need some help connecting an 8 pin current mode PWM controller to my boost converter circuit. Specifically this one. I have used controller IC's with integrated switches to make boost converters before, however, the amount of power I need to run through the circuit requires an external...