power

Hi everyone! I'm wondering what component is this? It is crunchy when you turn it like a sand inside and i think it needs a replacement. It doesn't control the power output properly. It is the two large object near the red led (one of it is crunchy)

I am trying to power an Odroid C4 board right now. Part: 1. Using a 3.7v 8000mAh Lithium battery (https://www.amazon.com/8000mAh-7565121-Battery-Rechargeable-Connector/dp/B07S84TSFH) Expect: 1. Need to be able to charge the battery using USB-C 2. It needs to output DC 12 V to connect to...

Hello, Im planning to do a very simple project but getting quite confused about where to start as I've done parts of it before but not brought everything together in one piece. Any advice on where to start would be great and I can expand my knowledge. Project Aims Simply put a box containing...

I am using Arduino and Controlling FAN which works on 48v. so i am using 2 power supply smps in my design. One for Arduino that 5V smps and another for FAN that is 48V smps. I want to use single power supply in my design that is of 48Vdc. I was looking for a buck converter that will take 48V as...

As shown in the diagram, I am trying to connect two power sources to load. The battery source is for emergency in the case of power outage of the wall source. I want the switching to be instantaneous with no interruption of power. What is the best solution to this problem? Is there a board...

Hey guys. I'm newbie to this forum i don't know if this is the right forum if not pardon. I'm here to ask what is rhe specifications of this speaker i can't see specifications at the back but i taken some pictures i am planing to rebuild this one. this speaker is from my deceased father. thank...

I have a 13s bms laying around and I want to use it as a 7s bms, is there a way to do that?any suggestions would be greatly helpful.

Hello, I am fairly new to electronics design (I have a mech e background), and am designing a board that requires dropping 12v to 5v with a large current requirement (up to 8A@5V). In a bid to save on BOM, I took a shot at creating my own design vs buying one off the shelf, using the...

Hello all, this is my first post here so be gentle. Currently enrolled in an Electrical Engineering program and finally finishing up next year. I have 7 years of avionic and airframe experience in the aerospace industry and more hours around automotive junk. I have worked plenty with coding, CAD...

I currently have a custom PCB design using the PIC16F1937-CN. The custom circuit gives an output voltage via the usb to an external device. I would like to charge my circuits battery with the same usb port which is currently not the case. It has another port for charging the device. What design...

hi to all i have a question about the AM signal power in am modulation in attach file i have derive the power of am signal but ther a term <m(t)> is the mean value of message i can ignore this term generally or in the case where the m(t) have zero offset? thank you George

Hi all. So I know that the impedance of the capacitor changes with frequency. However, stumbling across a document by KEMET and their new stacked MLCC capacitors which allow higher ripple current, https://www.mouser.co.uk/datasheet/2/212/1/KEM_C1105_KONNEKT_KC_Link_C0G-1855982.pdf There are...

How can I control the current that is supplied to a battery? I need to balance current consumption to avoid some parts of the system run out of power. My system is described in the attached file. I have a 12V input which goes into a Boost regulator to get 48V. Those 48V are used to feed a...

For Question 2.1, is the power 500W or 100W ? Do we need to apply the passive sign convention rule for power in whatever cases? Also, i’ve Learnt that we can check answers by balancing power in a circuit. But the power in this kind of circuits don’t balance out, but it is still valid. So when...

Hey everyone :) I'm working as an automation engineer and I've always asked myself why people say, that for example birds, can sit on power-lines, because they aren't touching neutral/different potential and no current is flowing. I can't really get this explanation into my head, because...

Hey there, i couldn’t fall asleep trying to solve following scenario: i have two power supplies running 24vdc in parallel, a main and one supplemental power supply. Both are being filtered with capacitors before supplying a single load. Now if one wants to run it, such that the supplemental...

Hi All, I would like to build a simple automatic irrigation system with Raspberry Pi zero, the thing is that I don't have access to electricity outside. I thought to connect 5v solar panel + 3\4 chargeable batteries. Im not that familiar with building control circuits for charging batteries...

Hello everyone, Hope you are all doing fine. I have been facing an electrical issue in my house since last Christmas. When the lights or any appliance with motor in any room are turned off/on the TV would go out and come back ON in a short span (as if the power went out and came back in a...

I have a simple DC power control circuit that I want triggered by reed relays. It is for model railroad use. One set of reed switches detects the passing of the train . The first switch turns the power on to a trolley car so as the train passes the trolley car is moving. The second reed switch...

Quarantine project: Adapting a Sony BFV-20W viewfinder Scroll down to skip the background info As a cinematographer, I've always really felt most comfortable shooting with a viewfinder. However modern electronic viewfinders all exist in the "prohibitively expensive" class of filmmaking...