amplifier

I'm looking into this (attached) schematic for a bass amp. I'm not sure, why the low voltage supply (+-16V) has his own transformer windings, regulators etc. but then it's connected to the hugh voltage rail? (I've circled in red) Thanks

Hi all, I bought capacitors of 22kµ instead of 2.2kµ. I was wondering whetther this circuit could still work with the 22kµ and what the effect is on the circuit. I'm not a electrical engineer so my knowledge is rather limited in this field. My best guess would be that these are used for the...

Hi All, I am trying to setup my Sony N500 Xplod Car Amplifier in home environment. I have presently a 20A fuse placed in a 25A socket of the Amplifier. Its input is 12V. So I believe a SMPS of 25A 12V will suffice its working. I am intending to change the 20A fuse to 25A as well to support...

I'm trying to modding HackRF one rtl-sdr card, regarding this articles card have problem with tx bellow 100 MHz, lots of user complains about burning card, precisely MGA-81563 chip, I already burn once MGA-81563, and I replaces two of them. Someone suggest LVA-123+, but pins construction are not...

I'm trying to detect the source of the problem and hope you can help me to where should i look for it. So when I'm raising the volume on the amplifier the hum gets more quiet then if its 0 volume.(Without any input, just the speaker connected) It's not ground loop probably. Already checked.

Hello I really need your help I need a circuit to change amp of Pwm Input : pwm 12V 5Amp Output: pwm 12V amp between 15-50 amp I have to say I don't know programming or program any type of IC I know I have to pay money for design a circuit like thus, but I live in Iran we can't and don't let...

Hi! I have bought a headphone amplifier which I have made small changes to. The two things I've done is: - disconnect the on-off button by soldering a cable between the poles - adding longer wires to the diode so that the led could be attached a bit from the amplifier What have happend...

Is the second pole in the node marked in red? I am not sure

So here's the circuit: I think M2 is a common source amplifier and M4 a common gate amplifier, so they form a cascode amplifier where the gain is given by : Av = -gm2 * r0, r0 is the impedance at the node where the drain of the common gate amplifier is at (Vop). r0 = ( [rds8 // (rds2a * (...

Hi all, My requirement is to connect an additional light in parallel to my car's interior cabin light. My car supports upto 10w and I already have a 2W LED bulb inside, and the additional light is about 25W, so connecting it directly is not an option. So I connected a 12v relay with the signal...

How can I reduce Noise in this circuit?

Hello everyone, I'm trying to use this board as an analog lock-in amplifier; however, I'm running into some difficulties due to a lack of any documentation on the use of this device in lock-in experiments, save for PhysicsOpenLab blog post that performs the experiment I'm trying to replicate...

Hello Everyone again, I have a continuation from my previous problem from my adjustments and testing that I was hoping to get help on. I am doing a multi channel mixer that pipes audio signals to different channels to go to different speakers. My previous post have pointed me to fixing the...

My amplifier panasonic su ch 7 stuck on standby. Why this problem and how can i solved it

I tried to make a preamp circuit but I'm not getting any output at all. The simulation on LTSpice seems to work well. The Op Amp I'm using is LMV821 datasheet I'm using a balanced dynamic microphone Zener Diode is 5V1. I don't mind if its noisy as long as I get a some sort of amplification from...

Hello! I have done calculations for designing a differential amplifier (DA) with differential output. I simulate (using cadence ) the DA with the calculated values and perform the DC analysis of the circuit to inquire all the transistors are operating in saturation. However, I did not get all...

Hi, I just have solved one of the bjt common emitter question below. However, I'm curious that how can I additionally find those things below: 1) Input and Output Impedance 2) AC Gain Here is the example and my hand draw solution. However, the question only asked to find Vout/Vin... Also, my...

I have this inverter and do not know how to compute gain gclosed as a function of R1,R2,R3,R4,R5 and R6?? V out = closed * Vin. Circuit is in attach file!!

Hi, I bought DIY amplifier board. And now I am trying to find what I did wrong. It can work for about 2 seconds and then sound dissappear. But power stays on, and LED is glowing I connected 24 volt toroid to start the board. In description it says that circuit is designed for 12 to 36 AC...

Hi all, I have a 807 vacuum tube and I want to make a CW RF amplifier with it. I am thinking of using transistors in pre amplifier and 807 as final power amp. I have only one tube so I cannot make push pull amp. First of all I need to know if it will be possible to make such RF amplifier. If...