hi
I want to program W25Q64JVS flash memory but it shows me the following error.

'1': Reading status register contents...

INFO:iMPACT:2219 - Status register values:

INFO:iMPACT - 0011 1100 1110 1100

INFO:iMPACT:2492 - '1': Completed downloading core to device.

'1': IDCODE is 'ef4017' (in hex).

'1': ID Check passed.

'1': IDCODE is 'ef4017' (in hex).

'1': ID Check passed.

'1': Erasing Device.

'1': Using Sector Erase.

'1': Erasing non-volatile quad-enable bit...

'1': Programming Flash.

'1': Reading device contents...

done.

'1': Verification completed.

'1'rogramming in x1 mode.

W25Q64BV Status Register Contents = 0x0200.

QUAD ENABLE : 1

STATUS REGISTER PROTECT 1 : 0

STATUS REGISTER PROTECT 0 : 0

SECTOR PROTECT : 0

TOP/BOTTOM PROTECT : 0

BLOCK PROTECT BIT 2 : 0

BLOCK PROTECT BIT 1 : 0

BLOCK PROTECT BIT 0 : 0

'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.

INFO:iMPACT - '1': Flash was not programmed successfully.

PROGRESS_END - End Operation.

Elapsed time = 76 sec
I designed this board myself and I will put some pictures of the flash memory connection for you.




In this section, you will see the settings that I made for programming.

 

This looks like the Xilinx Tool chain
Try the xilinx forum, they are very active and knowledgeable

 

This looks like the Xilinx Tool chain
Try the xilinx forum, they are very active and knowledgeable

Hello,

did you read this thread, I am not sure if it is exactly your case, but might be helpful:
https://forums.xilinx.com/t5/Sparta...gramming-failed-while-Spi-width-1/td-p/657605

Best Regards

 

Hello,

did you read this thread, I am not sure if it is exactly your case, but might be helpful:
https://forums.xilinx.com/t5/Sparta...gramming-failed-while-Spi-width-1/td-p/657605

Best Regards

Hello
I can not download from version 14.1. I am not allowed to download. You can send me a download link.

 

Hello
I can not download from version 14.1. I am not allowed to download. You can send me a download link.

Hello,

I am not sure about which link you are talking - if about schematic.pdf I attache this file to post.

 

Hello,

I am not sure about which link you are talking - if about schematic.pdf I attache this file to post.

Hello
No, I mean version 14.1 of xilinx ise software.
I can not download it. Due to the conditions of my country, I am not allowed to download from the site.

 

Hello,

what OS Linux or Windows? Are you sure that version number is 14.1? I can download it for you and give link on Google disk, but I don't know if it is not against this forum rules?

Best Regards

 

Hello,

what OS Linux or Windows? Are you sure that version number is 14.1? I can download it for you and give link on Google disk, but I don't know if it is not against this forum rules?

Best Regards

Windows

Thank you very much for your kindness. Someone suggested try version 14.1 and get the answer.
I do not know if it is against the law or not.

 

Hello
No, I mean version 14.1 of xilinx ise software.
I can not download it. Due to the conditions of my country, I am not allowed to download from the site.

@pooya_b

Can I highlight that its a criminal offence to supply Xilinx software to a destination on the US restricted list.

It seems that you are on that list ,
as such, it would be illegal for anyone here to share you the software.

https://www.xilinx.com/support/answers/44043.html

 

Moderation.
Thread Closed.