electronics circuits diagrams

  1. MissFluffy

    Does anyone here know where I could get a Longtek 6052 X-S duplex display?

    Does anyone here know where I could get a Longtek 6052 X-S, as mentioned on these websites? 1. https://www.electronicshub.org/digital-alarm-clock/ 2. https://makingcircuits.com/blog/how-to-make-a-simple-digital-clock-circuit-explained/ Are there any alternatives to it that works with my...
  2. V

    In-depth resources to create my own dual-axis solar tracker using 1 DC motor and 1 battery/power source

    Hi all, I'm quite new to electronics. I have a very basic understanding of DC circuits, but nothing too extreme, therefore I would like some help on how to create a dual-axis solar tracker using 2 LDRs, run off of a single DC motor, and 1 battery/power source (potentially looking into solar...
  3. M

    Troubleshooting Differential Signal Issues with DS26LV32

    Hello, I wanted to reach out to this wonderful community to seek some guidance regarding an issue I'm facing with the DS26LV32 and DS26LV31 ICs on my board. I believe your collective expertise and experience can help shed some light on this problem. In my current project, I am utilizing the...
  4. J

    is this possible? to connect the function generator to the power supply

    is it possible to connect the function generator to the power supply? and if its possible what is the input source?
  5. C

    How to find total current and phase shift for this Wien oscillator?

    I know that total impedance is Zp/(Zp+Zs) where Zp is parallel impedance and Zs is series impedance that can be calculated easily. Is total current equal to Vin/total impedance?
  6. A

    SMPS POWER SUPPLY issue help needed

    Hello i am an engineering student working on a project of Switch mode power supply with outputs of 12V 1Amp .For this reason i have used power integration software to design smps supply circuit *(Schematic attached )with 12V 1 Amp required outputs. I have implemented this Circuit on PCB as...
  7. Alex_Khan

    Understanding two Multivibrator models

    Hello, I simulated the two multivibrator models in CMOS technology using the cadence tool. I was expecting the model 2 with Schmitt trigger(ST) will show robustness in PVT (Process Voltage temperature) analysis as compared to model 1 due to ST. But this was not the case both the Models shows the...
  8. Z

    I'm constructing a audio amplifier in LT spice, some good starting points?

    Hello, i'm new here on AAC. I've seen alot of interesting topics, questions and answers here, so i would like to be part of it. Question: It is for a school assignment, and i'm choosing to build a multistage amplifier (Pre-amp and Power-amp). What is a good starting point when choosing values...
  9. K

    SMD Capacitor selection

    Hello everyone, How can we calculate the voltage rating of an SMD ceramic capacitor. Is it dependent on the package size?.
  10. G

    Component choices and general advice for a sensor fusion device for soil quality measurement

    For a university project, I am designing and am further required to build a sensor fusion device for soil quality measurement in agricultural soil. The device will measure the volumetric water content (VWC) in the soil, the temperature of the soil and the light levels that the soil is exposed...
  11. R

    Fan Regulator Feedback Generator

    Hello Everyone, I need help in to generate feedback for fan regulator to the controller. 1. AC Fan require 1 phase Ac supply (230VAC/50Hz) 2. Controller require DC voltage in range of 0 to 3V3 3. System is able to support all type regulator, there different type's...
  12. R

    What is Cmeu in an npn BJT operating in saturation mode ?

    I know Cmeu is parasitic capacitance in active mode. It's the B-C junction capacitance. But does it change when the npn is operating in saturation mode? Also in general(not just in saturation mode) what happens to Cmeu at increasing Vce? Does it increase? What other things happen to the...
  13. toby159

    How to connect E3JM-R4S4 PNP Sensor

    Hi, this is E3JM-R4S4, brown and blue connect to power supply. I wanted to know is it either black or brown connect to +load and the white connect to 0V? If is it so, I don't see the electric flow.
  14. B

    Triangle, Circle and V-Symbols meanings

    Hello everyone. Can anyone tell me whats the meaning of these highlighted symbols in the attached circuit diagram? I have highlighted only some of those symbols. Much appreciated.