TI has announced end of life of LM386

Thread Starter

RichardO

Joined May 4, 2013
2,270
Sad. What are hobbyists going to do when the present supply of the LM386 runs out?

From the Digi-Key site:
Part Status: End of Life; Last Time Buy Date: 09-28-2016. Minimums may apply.
 

Brevor

Joined Apr 9, 2011
297
It's not just the LM386, the list of parts to be discontinued is several pages long. A few others listed are the LM3914/3915 and the LM833.
 

crutschow

Joined Mar 14, 2008
34,280
Audio Guru hopes the 741 is on the list. :D:rolleyes:
........................
No such luck.
I think the 741 will be around as long as there's analog electronics, especially in third world countries.
One possible advantage of students using the 741 is that they immediately run into the glaring differences (and deficiencies) between the ideal op amp they studied and a real but poor one in practice (supply voltage limits, offsets, bandwidth, slew-rate, common-mode range, etc). :rolleyes:
 

ian field

Joined Oct 27, 2012
6,536
No such luck.
I think the 741 will be around as long as there's analog electronics, especially in third world countries.
One possible advantage of students using the 741 is that they immediately run into the glaring differences (and deficiencies) between the ideal op amp they studied and a real but poor one in practice (supply voltage limits, offsets, bandwidth, slew-rate, common-mode range, etc). :rolleyes:
If they wanted that much of a challenge, they'd bring back the 709.
 

bertus

Joined Apr 5, 2008
22,270
Hello,

I still have some LM301 chips laying around.
Are those also on the list?

For a lot of us it would be a greater loss when the 555 would be on the list.

Bertus
 

Attachments

ian field

Joined Oct 27, 2012
6,536
Hello,

I still have some LM301 chips laying around.
Are those also on the list?

For a lot of us it would be a greater loss when the 555 would be on the list.

Bertus
They might well start phasing out the bipolar version, but in relative terms the CMOS 555 is still new kid on the block.

Through hole parts of any description are probably at greater risk of being finished off.

It wasn't all that long ago that Zetex introduced a version of the 555 that can run off a single 1.5V cell.
 

GopherT

Joined Nov 23, 2012
8,009
It would be amazing if TI would come out with a great replacement for the LM386. <0.1 THD, 1 Watt, Ultra-low noise, wide input voltage range, wide amplification range, low input, DIP Package for hobbiests
 

ian field

Joined Oct 27, 2012
6,536

GopherT

Joined Nov 23, 2012
8,009
Yes, TI recently purchased NS and now they are discontinuing a lot of old NS parts.
Like a lot of acquisitions. After some executive decides to buy another company, the product managers and technology people decide that most of it is a pile of $h!t.
 

ian field

Joined Oct 27, 2012
6,536
Like a lot of acquisitions. After some executive decides to buy another company, the product managers and technology people decide that most of it is a pile of $h!t.
As long as people keep paying for the parts - small SE Asian firms will keep making them.
 

WBahn

Joined Mar 31, 2012
29,976
It would be amazing if TI would come out with a great replacement for the LM386. <0.1 THD, 1 Watt, Ultra-low noise, wide input voltage range, wide amplification range, low input, DIP Package for hobbiests
It would be nice, but volume manufacturer's aren't going to do much of anything for the hobbyist. If doing so is truly a low=cost, low-hanging fruit, then maybe. But it's not going to be a decision driver.
 

nsaspook

Joined Aug 27, 2009
13,079
Like a lot of acquisitions. After some executive decides to buy another company, the product managers and technology people decide that most of it is a pile of $h!t.
It's more about what old equipment can still be supported and what can easily be re-qualified on new equipment. Most of these old line parts are still being made on 6 inch 20+ year old equipment that's running on shoe-strings and bailing wire in a FAB that's long past it's prime. The safety requirements for legacy installs are pretty lax but when you have to consolidate equipment to another location it must meet modern requirements. People are currently dealing with some major technology transfer issues with products from old-school acquisitions. If you have a critical need for something from a company that was recently swallowed up by another, my advice is to buy what you need NOW.
 
Top