(This is an update of a previous post.)
I am building a scale airport for my almost 3 and almost 5 year old sons for their Siddley the Spyjet airplanes from Pixar’s Cars2. I’m posting an updated version of my original circuit, for which I got lots of input from this forum – thanks again!
Please see the attached schematics for the new circuit. I want lights on the jetways, alternating lights for the top of the air traffic control tower and 2 rotating radars – all with individual switches to turn them on/off.
I used an iPad app called iCircuits, which also simulates the circuit and includes a multimeter and oscilloscope. In most of the attached pictures there's a box in the bottom right (see below) which is the multimeter and the corresponding component is highlighted in blue on the schematic.
The circuit has 4 LED’s in parallel with each other, which are in parallel with two DC hobby motors which are in parallel with a 555timer sub circuit, that alternately flashes a red and a green LED.
Component parts include:
All LED’s are 2.2V, 20mA
2 x Hobby motors – 3V, 260mA, 30rpm
Various resistors
1 capacitor
555 timer
All powered by a 4.8V NiMH
MY QUESTIONS:
Re: MOTORS
The hobby motors are 3V and supposed to draw 260mA of current at 30RPM. BUT The circuit simulator shows they are running at 60RPM and 65.645mRPM. For the parameters of the motor see the attached picture. I had no idea what the “stall current” was so I input 530mA. I also didn’t know other parameters such as stall torque, inductance or inertia so I left those with the default settings of the simulator.
1. What’s up with the RPM? Why such drastic changes, is that going to be evident in the final product?
2. Should I be concerned about the other parameters?
3. Is there a way to figure out the stall current? I tried attaching my multimeter and stopping the motor but couldn’t get a stable reading, it was just fluctuating all over the place.
4. Also, the current of the motor shown by the simulator is fluctuating from 182mA to 183mA to 667mA. Since 667mA is way more than the 260mA draw current for the motor is this a problem? I’m thinking its okay but just wondering.
Re: 555 Circuit
This is a circuit based off a RR Xing blinker from 555-timer-circuits.com.
1. Is there a way that I can make these LED’s alternatively blink like they are but make them fade in and out?
Re: Zener Diodes
I was told the zener diode voltage should be whatever your battery voltage is minus the voltage requirement of the motor.
1. The current of the zener diode is all over the place, from 184mA, to 320mA, to 667mA, to 208mA, to 2.3A. Is that a problem or is that normal?
2. Also, the 2 settings in the simulator for the zener diode were “Fwd Voltage @1A”, which I left with the default, and “Zener Voltage @5mA”, which I set at 1.8V. Is this correct and should I do anything to change the “Fwd Voltage @1A” setting?
Thanks for any help/advice, its much appreciated.
I am building a scale airport for my almost 3 and almost 5 year old sons for their Siddley the Spyjet airplanes from Pixar’s Cars2. I’m posting an updated version of my original circuit, for which I got lots of input from this forum – thanks again!
Please see the attached schematics for the new circuit. I want lights on the jetways, alternating lights for the top of the air traffic control tower and 2 rotating radars – all with individual switches to turn them on/off.
I used an iPad app called iCircuits, which also simulates the circuit and includes a multimeter and oscilloscope. In most of the attached pictures there's a box in the bottom right (see below) which is the multimeter and the corresponding component is highlighted in blue on the schematic.
The circuit has 4 LED’s in parallel with each other, which are in parallel with two DC hobby motors which are in parallel with a 555timer sub circuit, that alternately flashes a red and a green LED.
Component parts include:
All LED’s are 2.2V, 20mA
2 x Hobby motors – 3V, 260mA, 30rpm
Various resistors
1 capacitor
555 timer
All powered by a 4.8V NiMH
MY QUESTIONS:
Re: MOTORS
The hobby motors are 3V and supposed to draw 260mA of current at 30RPM. BUT The circuit simulator shows they are running at 60RPM and 65.645mRPM. For the parameters of the motor see the attached picture. I had no idea what the “stall current” was so I input 530mA. I also didn’t know other parameters such as stall torque, inductance or inertia so I left those with the default settings of the simulator.
1. What’s up with the RPM? Why such drastic changes, is that going to be evident in the final product?
2. Should I be concerned about the other parameters?
3. Is there a way to figure out the stall current? I tried attaching my multimeter and stopping the motor but couldn’t get a stable reading, it was just fluctuating all over the place.
4. Also, the current of the motor shown by the simulator is fluctuating from 182mA to 183mA to 667mA. Since 667mA is way more than the 260mA draw current for the motor is this a problem? I’m thinking its okay but just wondering.
Re: 555 Circuit
This is a circuit based off a RR Xing blinker from 555-timer-circuits.com.
1. Is there a way that I can make these LED’s alternatively blink like they are but make them fade in and out?
Re: Zener Diodes
I was told the zener diode voltage should be whatever your battery voltage is minus the voltage requirement of the motor.
1. The current of the zener diode is all over the place, from 184mA, to 320mA, to 667mA, to 208mA, to 2.3A. Is that a problem or is that normal?
2. Also, the 2 settings in the simulator for the zener diode were “Fwd Voltage @1A”, which I left with the default, and “Zener Voltage @5mA”, which I set at 1.8V. Is this correct and should I do anything to change the “Fwd Voltage @1A” setting?
Thanks for any help/advice, its much appreciated.
Attachments
-
100.3 KB Views: 23
-
289.4 KB Views: 21
-
287.2 KB Views: 16
-
222.5 KB Views: 14
-
252 KB Views: 16
-
276.3 KB Views: 20
Last edited: