Transistor info

Discussion in 'Homework Help' started by TsAmE, Apr 21, 2010.

  1. TsAmE

    TsAmE Thread Starter Member

    Joined:
    Apr 19, 2010
    Messages:
    72
    I am having some trouble understanding the transistor and have a couple of things that I would like to know about transistors.

    1. Why is the output of a transistor at the collecter?

    2. How does a transistor invert a signal?

    3. When will a darlington resistor go on?
  2. kingdano

    kingdano Member

    Joined:
    Apr 14, 2010
    Messages:
    377
    Location:
    USA, Massachusetts
    1
    Functional model of an NPN transistor

    [​IMG]

    The operation of a transistor is difficult to explain and understand in terms of its internal structure. It is more helpful to use this functional model:
    • The base-emitter junction behaves like a diode.
    • A base current IB flows only when the voltage VBE across the base-emitter junction is 0.7V or more.
    • The small base current IB controls the large collector current Ic.
    • Ic = hFE × IB (unless the transistor is full on and saturated)
      hFE is the current gain (strictly the DC current gain), a typical value for hFE is 100 (it has no units because it is a ratio)
    • The collector-emitter resistance RCE is controlled by the base current IB:
    IB = 0 RCE = infinity transistor off
    IB small RCE reduced transistor partly on
    IB increased RCE = 0 transistor full on ('saturated')
  3. kingdano

    kingdano Member

    Joined:
    Apr 14, 2010
    Messages:
    377
    Location:
    USA, Massachusetts
    2.
    A transistor inverter (NOT gate)

    [​IMG]

    Inverters (NOT gates) are available on logic ICs but if you only require one inverter it is usually better to use this circuit. The output signal (voltage) is the inverse of the input signal:

    When the input is high (+Vs) the output is low (0V).
    When the input is low (0V) the output is high (+Vs).

    Any general purpose low power NPN transistor can be used. For general use RB = 10k[​IMG] and RC = 1k[​IMG], then the inverter output can be connected to a device with an input impedance (resistance) of at least 10k[​IMG] such as a logic IC or a 555 timer (trigger and reset inputs). If you are connecting the inverter to a CMOS logic IC input (very high impedance) you can increase RB to 100k[​IMG] and RC to 10k[​IMG], this will reduce the current used by the inverter.
  4. kingdano

    kingdano Member

    Joined:
    Apr 14, 2010
    Messages:
    377
    Location:
    USA, Massachusetts
    Darlington pair

    This is two transistors connected together so that the current amplified by the first is amplified further by the second transistor. The overall current gain is equal to the two individual gains multiplied together: Darlington pair current gain, hFE = hFE1 × hFE2
    (hFE1 and hFE2 are the gains of the individual transistors)
    This gives the Darlington pair a very high current gain, such as 10000, so that only a tiny base current is required to make the pair switch on.
    A Darlington pair behaves like a single transistor with a very high current gain. It has three leads (B, C and E) which are equivalent to the leads of a standard individual transistor. To turn on there must be 0.7V across both the base-emitter junctions which are connected in series inside the Darlington pair, therefore it requires 1.4V to turn on.



    [​IMG]
  5. kingdano

    kingdano Member

    Joined:
    Apr 14, 2010
    Messages:
    377
    Location:
    USA, Massachusetts
Similar Threads
Forum Title Date
Homework Help How to plot the Ib vs VBE and IC Vs VCE for a transistor with IB as the variable resistor? Oct 21, 2014
Homework Help BiPolar transistor Oct 17, 2014
Homework Help UJT transistor simple operating principle? Oct 13, 2014
Homework Help Voltage regulator with transistors Oct 8, 2014
Homework Help NPN transistor base voltage supplied Oct 5, 2014

Share This Page