Multisim Error

Discussion in 'Electronics Resources' started by zaidqais, Aug 23, 2009.

  1. zaidqais

    zaidqais Thread Starter Member

    Joined:
    Feb 14, 2009
    16
    0
    Hi all
    I am trying to make a circuit with multisim (software) but i get this error that I cant explain :(

    [​IMG]

    And the error log is

    Code ( (Unknown Language)):
    1. Instrument operation performed   (2009, August 23, Sunday, 21:44:35)
    2. |   Instrument Analysis: Transient Analysis #0  
    3. |   |   Plot title:
    4. |   |   Analysis settings
    5. |   |   |   Initial Conditions: Automatically generate initial conditions
    6. |   |   |   Starting time (TSTART): 0
    7. |   |   |   Stop time (TSTOP): 1e+030
    8. |   |   |   Plotting increment (TSTEP): automatically calculated (less than: 1e+030)
    9. |   |   |   Maximum time step (TMAX): automatically calculated (less than: 1e+030)  
    10. |   |   Perform consistency check
    11. |   |   Variables from analysis  
    12. |   |   Representation as SPICE commands
    13. |   |   |   begin-scope page
    14. |   |   |   checknodes 3
    15. |   |   |   save all
    16. |   |   |   iplot all
    17. |   |   |   set trtol = 7
    18. |   |   |   set itl4 = 100  
    19. |   |   |   set convlimit
    20. |   |   |   set rshunt = 1e+012  
    21. |   |   |   -param hrange 0 1e+030  
    22. |   |   |   save
    23. |   |   |   tran  -env-options 1e-005 1e+030 0 1e-005 auto_ic auto_tstep auto_tmax  
    24. |   |   |   if-error end-scope audit-log-show
    25. |   |   |   end-scope
    26. |   |   Analysis Options
    27. |   |   |   Truncation error overestimation factor: 7
    28. |   |   |   Upper transient iteration limit: 100
    29. |   |   |   Enable convergence assistance on code models
    30. |   |   |   Shunt resistance from analog nodes to ground: 1e+012
    31. |   Output from instrument analysis  
    32. Instrument operation performed   (2009, August 23, Sunday, 21:47:35)
    33. |   Instrument Analysis: Transient Analysis #0  
    34. |   |   Plot title:
    35. |   |   Analysis settings
    36. |   |   |   Initial Conditions: Automatically generate initial conditions
    37. |   |   |   Starting time (TSTART): 0
    38. |   |   |   Stop time (TSTOP): 1e+030
    39. |   |   |   Plotting increment (TSTEP): automatically calculated (less than: 1e+030)
    40. |   |   |   Maximum time step (TMAX): automatically calculated (less than: 1e+030)  
    41. |   |   Perform consistency check
    42. |   |   Variables from analysis  
    43. |   |   Representation as SPICE commands
    44. |   |   |   begin-scope page
    45. |   |   |   checknodes 3
    46. |   |   |   save all
    47. |   |   |   iplot all
    48. |   |   |   set trtol = 7
    49. |   |   |   set itl4 = 100  
    50. |   |   |   set convlimit
    51. |   |   |   set rshunt = 1e+012  
    52. |   |   |   -param hrange 0 1e+030  
    53. |   |   |   save
    54. |   |   |   tran  -env-options 1e-005 1e+030 0 1e-005 auto_ic auto_tstep auto_tmax  
    55. |   |   |   if-error end-scope audit-log-show
    56. |   |   |   end-scope
    57. |   |   Analysis Options
    58. |   |   |   Truncation error overestimation factor: 7
    59. |   |   |   Upper transient iteration limit: 100
    60. |   |   |   Enable convergence assistance on code models
    61. |   |   |   Shunt resistance from analog nodes to ground: 1e+012
    62. |   Output from instrument analysis  
    63. |   |   TRAN:  Timestep too small; time = 0.00393345, timestep = 1.25e-015: trouble with node 5  
    64. |   |   doAnalyses: Timestep too small  
    65. |   |  
    66. |   |  
    67. |   |   tran simulation(s) aborted  
    68. Instrument operation performed   (2009, August 23, Sunday, 21:47:47)
    69. |   Instrument Analysis: Transient Analysis #0  
    70. |   |   Plot title:
    71. |   |   Analysis settings
    72. |   |   |   Initial Conditions: Automatically generate initial conditions
    73. |   |   |   Starting time (TSTART): 0
    74. |   |   |   Stop time (TSTOP): 1e+030
    75. |   |   |   Plotting increment (TSTEP): automatically calculated (less than: 1e+030)
    76. |   |   |   Maximum time step (TMAX): automatically calculated (less than: 1e+030)  
    77. |   |   Perform consistency check
    78. |   |   Variables from analysis  
    79. |   |   Representation as SPICE commands
    80. |   |   |   begin-scope page
    81. |   |   |   checknodes 3
    82. |   |   |   save all
    83. |   |   |   iplot all
    84. |   |   |   set trtol = 7
    85. |   |   |   set itl4 = 100  
    86. |   |   |   set convlimit
    87. |   |   |   set rshunt = 1e+012  
    88. |   |   |   -param hrange 0 1e+030  
    89. |   |   |   save
    90. |   |   |   tran  -env-options 1e-005 1e+030 0 1e-005 auto_ic auto_tstep auto_tmax  
    91. |   |   |   if-error end-scope audit-log-show
    92. |   |   |   end-scope
    93. |   |   Analysis Options
    94. |   |   |   Truncation error overestimation factor: 7
    95. |   |   |   Upper transient iteration limit: 100
    96. |   |   |   Enable convergence assistance on code models
    97. |   |   |   Shunt resistance from analog nodes to ground: 1e+012
    98. |   Output from instrument analysis  
    99. |   |   TRAN:  Timestep too small; time = 0.00393345, timestep = 1.25e-015: trouble with node 5  
    100. |   |   doAnalyses: Timestep too small  
    101. |   |  
    102. |   |  
    103. |   |   tran simulation(s) aborted  
    104. Instrument operation performed   (2009, August 23, Sunday, 21:49:31)
    105. |   Instrument Analysis: Transient Analysis #0  
    106. |   |   Plot title:
    107. |   |   Analysis settings
    108. |   |   |   Initial Conditions: Automatically generate initial conditions
    109. |   |   |   Starting time (TSTART): 0
    110. |   |   |   Stop time (TSTOP): 1e+030
    111. |   |   |   Plotting increment (TSTEP): automatically calculated (less than: 1e+030)
    112. |   |   |   Maximum time step (TMAX): automatically calculated (less than: 1e+030)  
    113. |   |   Perform consistency check
    114. |   |   Variables from analysis  
    115. |   |   Representation as SPICE commands
    116. |   |   |   begin-scope page
    117. |   |   |   checknodes 3
    118. |   |   |   save all
    119. |   |   |   iplot all
    120. |   |   |   set trtol = 7
    121. |   |   |   set itl4 = 100  
    122. |   |   |   set convlimit
    123. |   |   |   set rshunt = 1e+012  
    124. |   |   |   -param hrange 0 1e+030  
    125. |   |   |   save
    126. |   |   |   tran  -env-options 1e-005 1e+030 0 1e-005 auto_ic auto_tstep auto_tmax  
    127. |   |   |   if-error end-scope audit-log-show
    128. |   |   |   end-scope
    129. |   |   Analysis Options
    130. |   |   |   Truncation error overestimation factor: 7
    131. |   |   |   Upper transient iteration limit: 100
    132. |   |   |   Enable convergence assistance on code models
    133. |   |   |   Shunt resistance from analog nodes to ground: 1e+012
    134. |   Output from instrument analysis  
    135. |   |   TRAN:  Timestep too small; time = 0.00393345, timestep = 1.25e-015: trouble with node 5  
    136. |   |   doAnalyses: Timestep too small  
    137. |   |  
    138. |   |  
    139. |   |   tran simulation(s) aborted  
    140. Instrument operation performed   (2009, August 23, Sunday, 21:49:36)
    141. |   Instrument Analysis: Transient Analysis #0  
    142. |   |   Plot title:
    143. |   |   Analysis settings
    144. |   |   |   Initial Conditions: Automatically generate initial conditions
    145. |   |   |   Starting time (TSTART): 0
    146. |   |   |   Stop time (TSTOP): 1e+030
    147. |   |   |   Plotting increment (TSTEP): automatically calculated (less than: 1e+030)
    148. |   |   |   Maximum time step (TMAX): automatically calculated (less than: 1e+030)  
    149. |   |   Perform consistency check
    150. |   |   Variables from analysis  
    151. |   |   Representation as SPICE commands
    152. |   |   |   begin-scope page
    153. |   |   |   checknodes 3
    154. |   |   |   save all
    155. |   |   |   iplot all
    156. |   |   |   set trtol = 7
    157. |   |   |   set itl4 = 100  
    158. |   |   |   set convlimit
    159. |   |   |   set rshunt = 1e+012  
    160. |   |   |   -param hrange 0 1e+030  
    161. |   |   |   save
    162. |   |   |   tran  -env-options 1e-005 1e+030 0 1e-005 auto_ic auto_tstep auto_tmax  
    163. |   |   |   if-error end-scope audit-log-show
    164. |   |   |   end-scope
    165. |   |   Analysis Options
    166. |   |   |   Truncation error overestimation factor: 7
    167. |   |   |   Upper transient iteration limit: 100
    168. |   |   |   Enable convergence assistance on code models
    169. |   |   |   Shunt resistance from analog nodes to ground: 1e+012
    170. |   Output from instrument analysis  
    171. |   |   TRAN:  Timestep too small; time = 0.00393345, timestep = 1.25e-015: trouble with node 5  
    172. |   |   doAnalyses: Timestep too small  
    173. |   |  
    174. |   |  
    175. |   |   tran simulation(s) aborted  
    176.  
    Thank you
     
    #1
Loading...