machine design

Discussion in 'The Projects Forum' started by fisa, May 15, 2012.

  1. fisa

    fisa Thread Starter New Member

    Joined:
    May 15, 2012
    Messages:
    6
    How can I cal calculate torque per volume of an electric machine? Should I cosider the stator diameter or rotor diameter of a machine?
  2. fisa

    fisa Thread Starter New Member

    Joined:
    May 15, 2012
    Messages:
    6
    What parameter effect on stack length of an electric machine?
  3. wayneh

    wayneh AAC Fanatic!

    Joined:
    Sep 9, 2010
    Messages:
    8,384
    Location:
    Roscoe, IL
  4. fisa

    fisa Thread Starter New Member

    Joined:
    May 15, 2012
    Messages:
    6
    I want to know how can I calculate torque per volume of a machine. Example Rotor diameter 70 mm, stator diameter 144 mm, stack length 60 mm and the torque is 9.55 Nm. then what is the torque per volume? More over can I choose any stack length of a machine arbitarily?
  5. wayneh

    wayneh AAC Fanatic!

    Joined:
    Sep 9, 2010
    Messages:
    8,384
    Location:
    Roscoe, IL
    So the question is, what is the volume? (You know the torque.) I think the definition of the volume is somewhat arbitrary and depends on the circumstances - whether to include the clearances required around the machine for instance.

    Are you asking if you can make the shaft longer to get more torque? Yes, you can essentially build multiple motors along a single shaft.
  6. P-MONKE

    P-MONKE Member

    Joined:
    Mar 14, 2012
    Messages:
    83
    Location:
    United Kingdom
    I think this should be a continuation of this thread: machine design
  7. bertus

    bertus Administrator Staff Member

    Joined:
    Apr 5, 2008
    Messages:
    12,754
    Location:
    Amsterdam,Holland (GMT + 1)
    Hello,

    I have merged the two threads.

    Bertus
  8. shortbus

    shortbus Senior Member

    Joined:
    Sep 30, 2009
    Messages:
    2,846
    Location:
    ohio,usa
  9. fisa

    fisa Thread Starter New Member

    Joined:
    May 15, 2012
    Messages:
    6
    Hello,
    I was wondering if someone could give the answers of the following questions regarding Interior permanent magnet synchronous machine(IPMSM)
    *What is the IEEE standard for machine(IPMSM) core losses?
    *How practically measure the core losses of a PMSM( separating windage loss and friction loss)?
    *How can I measure the moment of inertial of a IPMSM practically?
    *Is Distributed winding of a 3 phase machine, lap or wave winding or something else?
    * What max speed limit is in currently used IPMSM?
  10. shortbus

    shortbus Senior Member

    Joined:
    Sep 30, 2009
    Messages:
    2,846
    Location:
    ohio,usa
    This sounds like it should be in the homework section not the projects section.

    The is a lot of information in Google about " internal permanent magnet synchronous motors", if YOU look.

    IEEE does not set standards for motors. NEMA is one of the standards for motors.
Similar Threads
Forum Title Date
The Projects Forum Help with designing mutli relay/trigger game machine Feb 1, 2011
The Projects Forum converting washing machine motor to wood lathe power supply Nov 18, 2014
The Projects Forum Making an Espresso Machine Nov 4, 2014
The Projects Forum CONFIGURATIONS HMI (HUMAN MACHINE INTERFACE) CITECH FOR PLC OMRON CP2M Oct 27, 2014
The Projects Forum Drill machine connected with PC Oct 4, 2014

Share This Page