
Homework Help Stuck on a textbook question or coursework? Cramming for a test and need help understanding something? Post your questions and attempts here and let others help. 

Thread Tools  Display Modes 
#1




Tuned voltage amplifier
hello everyone
can anyone answer any these questions? 1.what are the effects of the reactance ,capacitance, impedance in the Tuned voltage amplifier? 2.what is the importance of center frequency and bandwidth of a Tuned voltage amplifier used in a radio receiver? 3.what is the selectivity of a Tuned voltage amplifier? 4.what is the Q factor of a Tuned voltage amplifier, and who can i find it or calculate it? answering any of them would be fine, and thanks either way 
#2




It might be that you need a text that deals with intermediate frequency (IF) amplifiers.
Unless, of course, you are curious about a tuned radio frequency (TRF) receiver.
__________________
First comes the hardware, then the software. 
#3




What text are you working from?
Basic Electronics and Linear Circuits (N. N. Bhargava, S. C. Gupta, D. C. Kulshreshtha) has this as chapter 11 Starting on page 369 it gives the answers pretty much right down the line. These are pretty easy to answer however, 1. has to do with the efficiency of the amplifier, if you are trying to amplify a higher frequency ( > 1MHZ) one starts dealing with resonance and power efficiency. In simple terms, if your amplifier is not tuned to the frequency you are amplifying you get power feedback which can destroy your amp. 2. Center frequency and bandwidth is about amplifying only the frequency you want to amplify. If you have, for example, harmonics off the main frequency you may not want to amplify them, only the frequency you are interested in. Think of out of band amplification (amplification of frequencies you don't want to amplify) as noise or distortion of the main signal. 3. Selectivity means how well can I amplify only the signal I want, not things I don't want to amplify such as harmonics. 4. You can find the q by knowing the reactance, we can call it X sub L (or C) and the result would be Q = X/R and X = w (omega or frequency) / R or omega = 2 pi frequency so you can write it Q = 2 pi Freq L/R. Kind of hard to write equations in this editor. the whole point to this is that if your amplifier is at resonance you can reduce your calculations to Ohms law. Does that help? 
#4




Thank you very much...
you see we haven't studied Tuned voltage amplifier at all, but we did work with it in lab then they asked us to do calculations and write a report about it...that's why the questions were easy and all.. but I think I can do it now thanks to you 
Tags 
amplifier, tuned, voltage 
Related Site Pages  
Section  Title  
Video Lecture  Inductors (Part 2)  Types and Applications  Inductors,Capacitors,Transformers  
Worksheet  Oscillator circuits  
Worksheet  Multistage transistor amplifiers  
Worksheet  Class A BJT amplifiers  
Worksheet  Performancebased assessments for AC circuit competencies  
Worksheet  Passive filter circuits  
Worksheet  Mixedfrequency signals  
Worksheet  Resonance  
Textbook  Radio circuits  INCOMPLETE : Practical Analog Semiconductor Circuits  
Textbook  Q and bandwidth of a resonant circuit : Resonance 
Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
Current to Voltage amplifier  sjkim0329  Homework Help  7  12172008 09:43 AM 
Treatise about Voltage  Ratch  Physics  100  05182008 07:55 AM 
Basic Single Tuned Amplifier  Steve1992  Homework Help  5  04222008 04:43 PM 
Current and voltage source  jasonhaykin  General Electronics Chat  9  04162008 07:45 PM 
tuned amplifier  neerajrocks  Homework Help  0  10232007 03:59 PM 
Thread Tools  
Display Modes  

