All About Circuits Forum  

Go Back   All About Circuits Forum > Electronics Forums > The Projects Forum

Notices

The Projects Forum Working on an electronics project and would like some suggestions, help or critiques? If you would like to comment or assist others with their projects, this is the place to do it.

Reply   Post New Thread
 
Thread Tools Display Modes
  #1  
Old 02-18-2013, 10:37 PM
JeffR JeffR is offline
New Member
 
Join Date: Feb 2013
Posts: 3
Default Using Raspberry Pi to control solenoid

Hi all, bit of an amateur looking for some advice. Have done quite a bit of web searching but want to validate my proposed design. The project is a little garden watering system controlled by the raspberry pi. The solenoids will have a light load, probably switched on for 20-30 minutes maximum once every 3 days or so.

We can skip all the logic and get to the electronics question - how to use the I/O from the pi to control the water valve solenoid.

I found a basic circuit design here http://davidhunt.ie/?p=2770

Since ultimately I will want to control 4-5 solenoids (for watering various areas), I then found a darlington array on an IC that seems to make sense. It looks like it has the diode protection already built into the chip. It looks like it can handle 500mA per output http://www.ti.com/lit/ds/symlink/uln2003a.pdf

Just want to check that all these parts will come together.

The solenoids are 12V and pull around 320mA http://www.adafruit.com/products/997...FUWd4AodBl8Alg

The pi IO control is 3.3V and can put out 16mA per pin to a total of 51mA.

I'll put a separate 12V DC feed to the uln2003a.

Questions:
- Is the 3.3V from the pi enough to drive the chip?
- Can I run several solenoids simultaneously, or will that be too much for the chip? I can run them sequentially if necessary.
- I was reading that these solenoids have a large load to initially lift them, then a lower load to keep them lifted. Is there any sense to integrating some kind of capacitor(s) into the circuit, or is it overkill?
- If for some reason the chip will not work, can you suggest the components for each individual circuit? I was thinking http://www.adafruit.com/products/976 http://www.adafruit.com/products/755 but don't know what resistor to use.

Thanks for any advice, and please go a bit easy on me if my terminology is not too perfect.
Reply With Quote
  #2  
Old 02-19-2013, 02:54 PM
JeffR JeffR is offline
New Member
 
Join Date: Feb 2013
Posts: 3
Default

Dang, 112 views and no replies? Am I missing some key info?
Reply With Quote
  #3  
Old 02-19-2013, 03:56 PM
MrChips's Avatar
MrChips MrChips is offline
Super Moderator
 
Join Date: Oct 2009
Posts: 9,078
Blog Entries: 24
Default

R-pi is a tad overkill. I would look at the arduino.
__________________
Most computer problems can be attributed to a simple problem - a loosewire behind the keyboard.

Reply With Quote
  #4  
Old 02-19-2013, 04:02 PM
JeffR JeffR is offline
New Member
 
Join Date: Feb 2013
Posts: 3
Default

Pi is already a done deal.

More on adding a capacitor to the circuit:

My thought is that the power required to hold the solenoid is much less than the power required to initially lift the solenoid. So a capacitor of some type seems to make sense. Not so much worried about the power savings (the solenoids will only engage for 10-20 minutes a few times a week), it's more about limiting the power going through the uln2003 and keep that from overheating.

Saw this as an example but need help with adjusting to my loads/voltages.

http://www.edn.com/design/components...-and-efficient
Reply With Quote
  #5  
Old 02-19-2013, 07:13 PM
Meixner Meixner is offline
Senior Member
 
Join Date: Sep 2011
Location: Chicago, USA
Posts: 116
Default

That circuit would work but it could only power one solonoid at a time. Myself I would not worry about the power savings. If you want to reduce the load on the uln2003 you could either run only one solonoid at a time or skip the uln2003 and use a separate transistor for each solonoid. Also you have to size your power supply for the number of solonoids you want to power at the same time. Also it's best to mount the protection diode at the solonoid.
Reply With Quote
Reply   Post New Thread

Tags
, ,


Related Site Pages
Section Title
Textbook LED sequencer : Digital Integrated Circuits


Similar Threads
Thread Thread Starter Forum Replies Last Post
Help in identifying components for telescope control system? knro The Projects Forum 11 12-04-2012 05:18 AM
Proportional Solenoid Valve Control eckcotech General Electronics Chat 20 01-31-2012 06:37 AM
air solenoid controller help drjekl The Projects Forum 15 01-16-2012 02:57 AM
Solenoid valve control with relays leonhart88 General Electronics Chat 18 08-09-2010 11:34 PM
designing a Solenoid devalvyas General Electronics Chat 9 11-25-2008 06:23 AM

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:50 AM.


User-posted content, unless source quoted, is licensed under a Creative Commons Public Domain License.
Powered by vBulletin
Copyright ©2000 - 2014, vBulletin Solutions, Inc.