All About Circuits Forum  

Go Back   All About Circuits Forum > All About Circuits Commmunity Forums > Off-Topic

Notices

Off-Topic A place to discuss anything other than electronics with other members. General conversation allowed, but please have consideration for your fellow members.

Reply   Post New Thread
 
Thread Tools Display Modes
  #1  
Old 03-01-2010, 08:17 PM
Mathematics! Mathematics! is offline
Senior Member
 
Join Date: Jul 2008
Location: Ma United States
Posts: 1,022
Default measurement ?

I have had a problem with installing a prehung door...

First I measured the rauf opening to be height 80 1/2"
width 33 1/2"

Then I measured a prehung door at home depot that was exactly 80 1/2"
But it said on it rauf opening for height is for 82 1/2" so where is this extra
2" comeing from mathematically if you measure the prehung door and the opening for it and they are both the same then why is it not fitting by a hair? Why do you need the extra 2" for the height on specifications of the prehung door?

Second I measure all the house doors in my place (just the door) and all of them measure 80" height wise ... when I went to home depot to just by a replacement door I noticed the height is always 80" standard...

But I measured my prehung doors size (just the door ) and it was 79" so
I guess I will have to special order every time I need to replace just the door for it??? All the prehung door doors are about 79" but the standard doors are 80"

WTF so everytime you install a prehung door and want to change just the door not the frame out them you would have to special order a 79" door....
Seems BS to me or you would have to shave an inch off ....???
Either way all these doors give that the door itself is 80" but when I measure it I get 79"... wondering if these measurements on the door that they say 80" because their measuring to where it hits the jamb door and spaces between door and jamb...

Either way I am totally confused and mathematically it is wrong anyway you slice it?

Another question why do they call 2 by 4 wood , it is not 2" b 4ft or anything like that so I am lost with what freaking measuring system their using....????????????????????????????

Thanks for any help because most of what I am doing depend on precise measurements and if their not labeling things correctly then no matter what I measure I will be off................
Reply With Quote
  #2  
Old 03-01-2010, 09:21 PM
blueroomelectronics's Avatar
blueroomelectronics blueroomelectronics is offline
Senior Member
 
Join Date: Jul 2007
Location: Toronto, Canada
Posts: 1,701
Default

Maybe a Home Depot or home DIY forum might get you the answer you need.
Reply With Quote
  #3  
Old 03-01-2010, 09:36 PM
someonesdad someonesdad is offline
Senior Member
 
Join Date: Jul 2009
Location: Northwest USA
Posts: 1,584
Default

Can't help with the doors. The doors around my house (about 40 years old) vary from 79" to 81".

The screwball American sizes of things developed over the years independently in each industry. Once entrenched, it is enormously difficult to get people to think differently. For example, 1/2 inch diameter pipe was once a half inch in inside diameter. As material strength improved, the wall thickness could be reduced, yet people wanted to keep the outside diameter the same. Look at all the different gauge dimensions for sheet, wire, plate, etc. And it's comparatively simple with linear measurements -- if you go into science/engineering, the problem is worse because of compound units. Ultimately, the real problem is all the units/conventions just increase the chances of errors. And it costs real money too (wasn't that one Mars mission lost because one software group used SI and the other used fps? And I think it was to the tune of $100 million or so (too lazy to look it up)).

2x4 lumber was so named because that is the size it is when it is rough cut. The finished size is about half an inch under the rough size. You quickly learn that a 2x4 is actually about 1.5x3.5 and get on with life. But, I agree, it is a bit aggravating for the beginner.

Oh, there's also cheap manufacturers. In the old days (when my kids say dad was running with the allosaurs), if you bought a piece of 3/4" plywood, it was -- surprise -- 3/4" thick. Nowdays the skinflint manufacturers have figured out how to shave off thickness to save money -- I haven't seen a real 3/4" thick chunk of plywood in years. So greed enters into the equation also...
Reply With Quote
  #4  
Old 03-01-2010, 09:42 PM
Mathematics! Mathematics! is offline
Senior Member
 
Join Date: Jul 2008
Location: Ma United States
Posts: 1,022
Default

I am just wondering because it seems like a common error.

And for the 2 by 4 wood that is the rough lumber before planning the 1/2 " off of it. (orignal the wiki said 2 by 4 where exactly made 2" by 4" for the width and depth then some moron's kept changing that.

It just seems <snip> to sell something with a name that implies a different measurement

I know now that 2 by 4 finished lumber is 1 1/2" by 3 1/2" some day maybe it will be different and they wonder way we have building falling over some times....

As for the door I am still totally stumbed if you are selling a prehung door wouldn't you want to have the door compatible so you could buy a replacement door ..... I would think 80" should be really 80" to make all the doors compatible.

I will try to poke around on another forum that may have more info on the subject

I have been a scientist/mathematician for many years except now I am getting into building stuff and seeing how the materials aren't mathematically correct is alittle bit wierd. Since if people want to be precise they should rely on precise name meanings for things ..... just to make it easy on the mind if anything else

later

thanks

gotcha

Last edited by beenthere; 03-01-2010 at 11:03 PM. Reason: language
Reply With Quote
  #5  
Old 03-01-2010, 10:36 PM
SgtWookie's Avatar
SgtWookie SgtWookie is offline
Expert Member
 
Join Date: Jul 2007
Location: In the vast midwest of the USA; CST
Posts: 22,000
Default

Just wait until you find out that your door frames aren't really rectangular, either - rather more like a parallelogram made out of barrel staves
__________________
General info:
If you have a question, please start a thread/topic. I do not provide gratis assistance via PM nor E-mail, as that would violate the intent of this Board, which is sharing knowledge ... and deprives you of other knowledgeable input.
Reply With Quote
  #6  
Old 03-01-2010, 11:01 PM
Mathematics! Mathematics! is offline
Senior Member
 
Join Date: Jul 2008
Location: Ma United States
Posts: 1,022
Default

yeah , but that is what the shims and a level are for
And I got lucky and everything happens to be almost level.
But I know what you are talking about

Just so happens when I was doing the measurements that is what was screwing me up........

Last edited by Mathematics!; 03-01-2010 at 11:08 PM.
Reply With Quote
  #7  
Old 03-02-2010, 04:57 AM
loosewire loosewire is offline
Senior Member
 
Join Date: Apr 2008
Location: Fort Lauderdale, Florida - Broward County
Posts: 1,574
Blog Entries: 9
Default

That why they Invented a proper word,tradesman that Is good In
his craft,what ever It Is.
Reply With Quote
Reply   Post New Thread

Tags


Related Site Pages
Section Title
Worksheet Latch circuits
Worksheet CMOS logic gates
Worksheet Linear computational circuitry
Worksheet Thyristor application circuits
Worksheet Regulated power sources
Worksheet Bipolar junction transistors as switches
Worksheet Passive filter circuits
Worksheet Resonance
Worksheet DC bridge circuits
Worksheet Kirchhoff's Laws


Similar Threads
Thread Thread Starter Forum Replies Last Post
Isolated Voltage Measurement with Atmega8 adamj12b General Electronics Chat 2 08-05-2009 10:51 PM
Tcs230 color measurement problem thavamaran The Projects Forum 2 05-12-2009 01:28 PM
Biomedical Circuits : Body Impedance Measurement gokhalej The Projects Forum 1 04-22-2009 10:58 AM
opamp current direction in e-book swty_todd General Electronics Chat 62 04-02-2009 11:18 PM
HV current measurement 95se5m The Projects Forum 2 01-27-2007 03:35 AM

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 09:25 AM.


User-posted content, unless source quoted, is licensed under a Creative Commons Public Domain License.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.